Piston Seal

K753 - Piston Seal

General Features
Technicial Specifications

KASTAŞ NO	D (H9)	Ød (h9)	B (-0/+0,2)	r	ORING	X RING
K753-016	16	5	4,2	1	4,34X3,53	12,42X1,78
K753-022	22	11	4,2	1	10,69X3,53	17,17X1,78
K753-025	25	14	4,2	1	13,87X3,53	20,35X1,78
K753-028	28	17	4,2	1	15,47X3,53	23,52X1,78
K753-030	30	19	4,2	1	18,66X3,53	25,12X1,78
K753-032	32	21	4,2	1	20,22X3,53	26,70X1,78
K753-035	35	24	4,2	1	23,40X3,53	29,87X1,78
K753-040	40	29	4,2	1,3	28,17X3,53	34,65X1,78
K753-042	42	31	4,2	1,3	29,75X3,53	37,82X1,78
K753-045	45	34	4,2	1,3	32,92X3,53	37,82X1,78
K753-050	50	39	4,2	1,3	37,69X3,53	44,17X1,78
K753-050/1	50	34,5	6,3	1,8	32.69 x 5.	44.17 x 1.
K753-052	52	41	4,2	1,3	40.87X3.53	47.35X1.78
K753-055	55	44	4,2	1,3	44.04.X3.5	50.52X1.78
K753-060	60	49	4,2	1,3	47.22X3.53	53.70X1.78
K753-063	63	52	4,2	1,3	50.39X3.53	56.87X1.78
K753-063/1	63	47,5	6,3	1,8	47 x 5.33	56.87 x 1.
K753-065	65	54	4,2	1,3	53.57X3.53	60.05X1.78
K753-070	70	59	4,2	1,3	56.74X3.53	63.22X1.78
K753-070/1	70	54,5	6,3	1,8	53.34 x 5.	63.22 x 1.
K753-075	75	64	4,2	1,3	63.09X3.53	69.57X1.78
K753-080	80	64,5	6,3	1,8	62.87X5.33	72.75X1.78
K753-080/1	80	59	8,1	1,8	58 x 6.99	71.12 x 2.
K753-085	85	69,5	6,3	1,8	69.22X5.33	75.92X1.78
K753-090	90	74,5	6,3	1,8	72.39X5.33	82.27X1.78
K753-095	95	79,5	6,3	1,8	78.74X5.33	88.62X1.78
K753-100	100	84,5	6,3	1,8	81.92X5.33	88.62X1.78
K753-100/1	100	79	8,1	1,8	77 x 6.99	88.57 x 2.
K753-105	105	89,5	6,3	1,8	88.27X5.33	94.97X1.78
K753-110	110	94,5	6,3	1,8	91.44X5.33	101.32X1.7
K753-115	115	99,5	6,3	1,8	97.79X5.33	107.67X1.7
K753-120	120	104,5	6,3	1,8	100.97X5.3	114.02X1.7
K753-125	125	109,5	6,3	1,8	107.32X5.3	114.02X1.7
K753-130	130	114,5	6,3	1,8	113.67X5.3	120.37X1.7
K753-135	135	114	8,1	1,8	113.67X6,9	126.67X2.6
K753-140	140	119	8,1	1,8	116.84X6,9	126.67X2.6
K753-150	150	129	8,1	1,8	126.37X6,9	139.37X2.6
K753-160	160	139	8,1	1,8	135.89X6,9	145.72X2.6
K753-170	170	149	8,1	1,8	145.42X6,9	158.42X2.6
K753-180	180	159	8,1	1,8	158.12X6,9	171.11X2.6
K753-190	190	169	8,1	1,8	164.47X6,9	177.47X2.6
K753-200	200	179	8,1	1,8	177.17X6,9	190.17X2.6
K753-210	210	189	8,1	1,8	183.52X6,9	196.52X2.6
K753-220	220	199	8,1	1,8	196.22X6,9	202.87X2.6
K753-240	240	219	8,1	1,8	215.27X6,9	221.92X2.6
K753-250	250	229	8,1	1,8	227.97X6,9	234.62X2.6
K753-250/1	250	225,5	8,1	1,8	221.62 x 6	234.62 x 2
K753-310	310	282	9,5	2,5	279 x 8.4	291.69 x 3
K753-350	350	322	9,5	2,5	319.5 x 8.	329.8 x 3.

K753 is a three piece double acting sealing set which consists of one special mixture PTFE profile ring , one X-ring as for main sealing element and an O-ring as energizing element.

PRODUCT ADVANTAGES
• Wide range of temperature and chemicals depending on the o-ring and x-ring material
• Low friction , free of stick-slip
• High sealing effect in applications requiring media separation
• Low gas permeation rate
• Minimum static and dynamic friction coeffcient for a minimum energy loss and operating temperature
• Simple groove design and low axial housing heights

APPLICATION
Accumulators , heavy duty cylinders , presses and machine tools.

MATERIAL		CODE
NBR	70 SHORE A	NB_⁷⁰⁰¹
PTFE		PT_⁶⁰⁰³

OPERATING CONDITIONS

MEDIA

Mineral oils (DIN 51524)

HFA ve HFB

HFC

TEMPERATURE

-30°C +105°C

+5°C +60°C

-30°C +60°C

PRESSURE

≤400 Bar

SPEED

≤2.0 m/sn

Note: The above data are maximum values and cannot be used at the same time.

SURFACE ROUGHNESS	Ra	Rmax
Sliding Surface ØD	≤0.2 μm	≤2.0 μm
Groove Base Ød	≤1.6 μm	≤6.3 μm
Groove Flanks B	≤3.2 μm	≤15 μm
Note: It is recommended to have 50% to 90% of the working surface material contact area value.
INSTALLATION It is recommended to assembly into one piece piston with special assembly tool (See section; Hydraulic Sealing Elements General Installation Information). It is very important that the assembly tools must be of soft material and have no sharp edges. Before installation the sealing element must be oiled with system oil. NOTES It is recommended to use with minimum two piston guide rings in long stroke cylinders , minimum one guide ring in short stroke and low radial loaded cylinders. For special applications that require high temperatures or resistance to chemicals , piston seal is being manufactured with special mixture PTFE and FKM material. The permissible sealing gap values of K753 piston seal is given in the below table.

PERMISSIBLE SEALING GAP

B (mm)	Smax (mm)
	150 Bar	250 Bar	400 Bar
0.25	0.15	0.10	4.2
6.3	0.30	0.20	0.15
8.1	0.30	0.20	0.15
9.5	0.50	0.25	0.20

Note: The largest sealing gap value occurring on the non-pressurized side of the seal does have a vital importance for the function of the seal and in this respect it is quite important to use the S value lower than the above indicated numbers.